Table of Content
Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily. Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Add a rubber band to keep the display securely in place while you work. The iSclack is designed to safely open your iPhone enough to separate the pieces, but not enough to damage any of the display cables. Place the bottom of your iPhone in between the suction cups. Pull up on the small nub on the suction cup to remove it from the display. Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Taping Over The Display
I work at an Apple repair centre in based in the UK and we have recently encountered MAJOR issues with replacement home buttons. It turns out that home buttons are linked too the logic board on each handset due to the method in which Apple stores you biometric data. Due to this, to the greatest extent of our knowledge, any update will cause an ERROR 53 to occur. As of yet we have not be able to rescue a handset from this state.
Optionally, apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute. You can also use this guide to replace the home button bracket. Use a set of tweezers to carefully pull the gasket up from the home button. There is power on the second logic-board connector from top, misplacing it while assembly can cause short circuit. Your replacement part may come with an extra Phillips screw already installed left of the Home Button.
Lot of iPhone 6, 6+, 6s, 6s+, LCD Screens With Digitizers - Black And White 1 Ea
Remove the unnecessary screw so that you can reinstall the home button bracket. If you are replacing a broken front panel, there may be glass shards stuck to the home button. Carefully remove any remaining glass before transferring your home button to a new display.
The rubber gasket surrounding the home button is very thin and tears easily. Carefully wedge the tip of a spudger underneath the home button connector cable. Be sure the cup is pressed securely onto the screen to get a tight seal. Close the handle on the iSclack, opening the suction cup jaws. If the plastic depth gauge is attached at the center of the iSclack, remove it now—it's not needed for larger phones like the iPhone 6 Plus.
NEW Broadcom Touch IC Chip BCM5976C0KUB6G BCM5976 u12 for Repair iPhone 5/5S/5C
The information that comes from the digitizer transfers through a digitizer flex cable to an LCD. Whether you have an iPhone 6 or iPhone 6 Plus, there are specific digitizer to fit your phone and for proper screen replacement. You can obtain an individual screen or a pack that has multiple digitizers for whenever you need to repair your phone or help with the replacement of another phone. Repair kits come with all the necessary tools and equipment necessary to perform a screen replacement. For anyone who has damaged their iPhone 6 Plus screen from either deep scratches or having it badly cracked, screen replacement is a necessity but also a headache. The replacement of a screen can sometimes be costly especially for larger smartphones with bigger screens like the iPhone 6 Plus.
To reassemble your device, follow these instructions in reverse order. Remove the home button bracket from the front panel assembly. Remove the two 1.8 mm Phillips screws securing the home button bracket to the front panel. During reassembly, align the clips just below the top edge of the rear case. Then, slide the front panel upward until its top edge is flush with that of the rear case.
While still supporting the front panel, use a fingernail or the edge of an opening tool to disconnect the front-facing camera and earpiece speaker connector. While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case. Center the suction cups and press them firmly onto the top and bottom of the iPhone.
Whether you need to repair or have a full replacement of the digitizer or LCD, it may be more cost effective to get the parts separately and repair them yourself. Using the flat end of the spudger tool, disconnect the front-facing camera, sensor cable connector, and the home button cable connector. Replacement LCD screens are available for the iPhone 6 Plus for both white and black phone models. Included in the packages offered are a variety of different parts of the front side of the phone. Select listings for LCD and touchscreen replacements have product options that are compatible with multiple phone models.
Use a spudger or a fingernail to disconnect the home button cable connector. As technology advances, there’s still room for dreadful technical malfunctions like, error 53. This common error occurs when replacing a broken home button’s Touch ID on the iPhone 6/6 Plus with an unoriginal part from another phone, or a damaged flex cable. To fix this annoying error, replacing a basic accessory i-e USB cable is a quick and inexpensive fix.
The only problem I experienced was that you have to re-use the black gasket around the home button. It was tricky to have to place it on the new home button, but I got it after a few tries. Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it. Insert the flat tip of the spudger under the right edge of the display. Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case. The safest place to pry from is the notch in the front panel above the headphone jack.
Several clips along the top edge of the front panel form a partial hinge, allowing the front panel assembly to swing open like a book. Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone. Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.
If you’re within your one-year Apple Care warranty, Apple will charge you $79.00 to repair your broken home button. If your Apple Care warranty has expired, expect to pay approximately $200.00 for all iPhone 6/6 Plus home button repairs. Using the top of the phone as a hinge, pull the home button end of the front panel away from the rear case. Release the power button and then press and hold the home button until the, “slide to power off” slider vanishes. Repeatedly slamming your finger into a broken, sticky, or burning hot iPhone 6/6 Plus home button won’t magically fix your crippled device.
Step 27
Use the pointed end of a spudger to pry the lightly-adhered home button flex cable off the display assembly. Disconnect the home button/fingerprint sensor cable by prying it straight up from its socket on the logic board. Apply a suction cup to the lower left corner of the display assembly.
Take your suction cup and press it right above the home button ensuring it’s securely tight on the screen. If the cable doesn't separate easily, apply heat using an iOpener or hair dryer to soften the adhesive, and try again. Use the tip of a spudger to disconnect the home button connector from its socket on the home button cable. When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.
No comments:
Post a Comment